Hummingbird Scupper Transducer Install on Ocean Torque |
Thursday, 24 February 2011 08:07 |
Posts and DIY threads for this install are few and far between so I figured that I would keep a
photo journal of how I made this install. I really didn't know what to expect going in and I'm
happy to say that it was one of my easiest installs ever.
If you have an Ocean Kayak Trident or Prowler series then it has the Hummingbird Scupper Hole
that accepts the transducer. The following is the procedure for swapping out the shoot thru hull design;
I spoke with John Oast, Ocean Kayak Pro Staffer that helped me get this ball rolling. He also helped
to get me in touch with the right people. You will need to call Hummingbird and explain that you would
like to swap a brand new Shoot Thru (Transom Mount Transducer) for the Scupper Hole Transducer.
You might need to go through a few people before you get someone that can help you. Be persistent.
(I spoke with a rep from Johnson Outdoors who told me they are still training staff on the Scupper
Transducer swap.) Even though there was some confusion at first on how to get this done, I
found everyone at Hummingbird to be friendly and helpful, which is a nice change when it
comes to customer service.
When you speak with a rep you will get a work order #. Write that # on the outside of the shipping box as well as in a letter attached to your transducer inside the box. YES DO BOTH!
KEEP YOUR POWER CABLE if it's separate from the transducer cable. Pack and send your transducer AND the mounting hardware to the address they give you. Only send the mounting
hardware, DO NOT SEND THE FISH FINDER OR GPS PARTS or HARDWARE.
It'll take approx two weeks and is free of charge! Shipping only cost me $7. CORPORATE HEADQUARTERS Humminbird 678 Humminbird Lane Eufaula, AL 36027 Phone: 1-800-633-1468
The install location was clearly marked by the folks at Ocean Kayak Hull side view of the Scupper Hole Port
Simply tighten the nylon/plastic nut (not too tight though)
View of the installed scupper hole transducer from underneath There are many wiring variations. This is the route that I chose as I felt that it put the least amount of bend and stress on the wire itself. I used a hole saw to drill
through the hull. I plan to use the Liquid Tite Fittings pictured below to close and
streanthen the area that needed to be drilled. I have used these fittings on other
installs and they work great.
You will have a lot of extra wiring. You should coil and wire tie this out of the way to protect it from shifting bow hatch storage items
Again a Liquid Tie Fitting will be used to seal off and streanthen the drilled hole I chose to run my wires through the snap out grooves in the rear of the unit
All together now This is not a conventional plattform that I used to mount the head unit. I wanted a place to hang my bucktails as I switched them up. I made this platform from a sheet of vinyl and pre-drilled holes to accomodate the hooks. My plan is to store the head unit in the battery console (rod pod for non Torques) during
transit. The console lid will only put minimun pressure on the wires which should be fine.
Liquid Tite Fittings are available at kayakfishinggear.com They are available in 3/8, 1/2, and 3/4
|
Login
Newsletter
Also of Interest
Most Popular
Crabbing From the Kayak
The apron was my design after I caught my first crabs and tried to sort them in the kayak. You should have had pictures of that. I went to a local sail maker and told him what I...
The apron was my design after I caught my first crabs and tried to sort them in the kayak. You should have had pictures of that. I went to a local sail maker and told him what I...
Kayak Fishing for White Seabass
Ghost Busting - When Hunting White Seabass, Silence is Only One of a Kayaker’s Weapons.Reprinted courtesy of KayakFishingZone.com: Paddling the U.S. Pacific Coast and Baja Each...
Ghost Busting - When Hunting White Seabass, Silence is Only One of a Kayaker’s Weapons.Reprinted courtesy of KayakFishingZone.com: Paddling the U.S. Pacific Coast and Baja Each...
Myrtle Beach Sharkin
I got back last night at about midnight after a great 8 days at Myrtle Beach. I brought my kayak down again and had perfect weather every day with temps in the low 90's with a...
I got back last night at about midnight after a great 8 days at Myrtle Beach. I brought my kayak down again and had perfect weather every day with temps in the low 90's with a...
Random
Costa Rica Trip Report
My name is Judd Schreiber. I wanted to send you a report from a kayak fishing trip with kayak fishing guide, Ralph Solano, in Costa Rica. I usually surfcast for stripers in...
My name is Judd Schreiber. I wanted to send you a report from a kayak fishing trip with kayak fishing guide, Ralph Solano, in Costa Rica. I usually surfcast for stripers in...
Crabbing From the Kayak
The apron was my design after I caught my first crabs and tried to sort them in the kayak. You should have had pictures of that. I went to a local sail maker and told him what I...
The apron was my design after I caught my first crabs and tried to sort them in the kayak. You should have had pictures of that. I went to a local sail maker and told him what I...
Chasing Rainbows in a Kayaks
Chasing the Rainbow with South Texas Kayak My name is Jeff York; I am a kayak guide and a co-owner of South Texas Kayak (www.SouthTexasKayak.com). After proudly serving 20 years...
Chasing the Rainbow with South Texas Kayak My name is Jeff York; I am a kayak guide and a co-owner of South Texas Kayak (www.SouthTexasKayak.com). After proudly serving 20 years...